An AS568 dash number fixes two dimensions at once: an inside diameter and a cord thickness. Each carries a ±. This sub-library holds 367 rings with both tolerances in the data and 2 whose ID tolerance is withheld, and the two tolerances are not written to the same rule.

Two numbers, two rules

SeriesCord (in)Cord toleranceCord ±RingsID tolerance stepsID range (in)ID ±
0-series0.0400.0037.50%110.00413.79%
0-series0.0500.0036.00%110.0049.52%
0-series0.0600.0035.00%110.0047.14%
0-series0.0700.0034.29%47130.005–0.0370.63%–7.14%
1-series0.1030.0032.91%77170.005–0.0550.56%–10.20%
2-series0.1390.0042.88%84200.005–0.0850.43%–2.92%
3-series0.2100.0052.38%87290.005–0.1200.45%–1.50%
4-series0.2750.0062.18%49160.033–0.1200.45%–0.74%
9-series0.0560.0035.36%110.0052.70%
9-series0.0640.0034.69%210.0051.66%–2.09%
9-series0.0720.0034.17%210.0051.21%–1.42%
9-series0.0780.0033.85%110.0051.07%
9-series0.0820.0033.66%110.0071.32%
9-series0.0870.0033.45%110.0091.40%
9-series0.0970.0033.09%210.0091.19%–1.27%
9-series0.1160.0043.45%630.009–0.0120.85%–1.04%
9-series0.1180.0043.39%420.014–0.0180.77%–0.95%

Look at the two tolerance columns together. The ID tolerance takes 38 distinct values across these rings; the cord tolerance takes 4. The cords themselves span 0.040 to 0.275 in — ×6.88 — and the ID runs from 0.029 to 25.940 in, ×894.48. One of those spans is described by four numbers.

The cord tolerance barely moves

Cord tolerance (in)Cords it covers (in)GroupsRingsCord ±
0.0030.040, 0.050, 0.056, 0.060, 0.064, 0.070, 0.072, 0.078, 0.082, 0.087, 0.097, 0.103121372.91%–7.50%
0.0040.116, 0.118, 0.1393942.88%–3.45%
0.0050.2101872.38%
0.0060.2751492.18%

±0.003 in covers 12 of the 17 cord sizes here, all the way up to a 0.103 in cord. 3 of the remaining cords are held to ±0.004, and the two largest to ±0.005 and ±0.006.

That is an absolute figure, not a proportional one, and the consequence sits in the Cord ± column: the thinnest cord here is held to ±7.50% of itself and the thickest to ±2.18%.

Between those ends the share falls as the cord grows — with one reversal. From 0.103 to 0.116 in the tolerance steps from ±0.003 to ±0.004, an increase of 33.33%, while the cord itself grows by only 12.62%. The share goes up, from 2.91% to 3.45%.

So a thicker cord does not always get a looser percentage, and "the cord tolerance is x% of the cord" is wrong everywhere: on this data it runs from 2.18% to 7.50%.

The ID ladder has 38 steps

From ±0.004 to ±0.120 in. It is not an arithmetic series — the steps are uneven, and which step a ring lands on depends on its bore and, as the next section shows, on its series.

Applied to the smallest ring here, -001 at 0.029 in, the tolerance is ±0.004 in — ±13.79% of the bore. At the other end, -475 at 25.940 in takes ±0.120 in, which is ±0.46%.

The tightest share in the whole sub-library is not at that top end. It is -281, a 14.984 in bore at ±0.065 in, which is ±0.43% — tighter in relative terms than the 25.940 in ring. The reason is a flat rung, not the top of a ladder: the 2-series holds ±0.065 in over 6 consecutive bores, from 10.984 to 14.984 in, so the share falls the whole way across that run. One step further up the bore, ±0.075 in on 15.955 in, puts it back to ±0.47%.

Inside one series the ladder never reverses. Sort the rings of any series by bore and the tolerance is non-decreasing; the build checks all six series and refuses to publish if one goes backwards. The steps are not shared out evenly either: the 0-series 14, the 1-series 17, the 2-series 20, the 3-series 29, the 4-series 16 and the 9-series 7.

A ladder per series, not per size

ID (in)Looser ringToleranceTighter ringToleranceGap (in)
0.924-119 (1-series)0.010-912 (9-series)0.0090.001
1.171-217 (2-series)0.012-916 (9-series)0.0100.002
1.475-325 (3-series)0.015-920 (9-series)0.0140.001
4.475-425 (4-series)0.033-349 (3-series)0.0300.003
4.600-426 (4-series)0.033-350 (3-series)0.0300.003
4.725-427 (4-series)0.033-351 (3-series)0.0300.003
4.850-428 (4-series)0.033-352 (3-series)0.0300.003
8.475-446 (4-series)0.055-371 (3-series)0.0500.005
8.975-447 (4-series)0.055-373 (3-series)0.0500.005
11.475-380 (3-series)0.065-452 (4-series)0.0600.005
11.975-381 (3-series)0.065-453 (4-series)0.0600.005
12.975-382 (3-series)0.065-455 (4-series)0.0600.005

Twelve bores in this sub-library carry two different ID tolerances, because two series each grew their own ladder over the same bore. The gap is 0.005 in at 5 of the twelve; the first is 8.475 in, where -446 in the 4-series takes ±0.055 and -371 in the 3-series takes ±0.050.

The same thing shows up as a fall rather than a tie. Stepping up one bore at a time through the sorted sub-library, 47 times the larger ring is the tighter one. The sharpest is -102 at 0.049 in with ±0.005 in against -003 at 0.056 in with ±0.004 in: a bore 14.29% larger, held 20.00% tighter.

Which is why "what is the ID tolerance at 8.475 in" has no single answer. The question needs the series, and on a drawing the series is the dash number — a three-digit number that says nothing about tolerance until it is looked up.

Where the two sources disagree

RingCord (in)Cord toleranceApple (in)Trelleborg (in)Gap (in)
-4690.2750.0060.0900.0950.005
-4700.2750.0060.0900.0950.005

Both are 0.275 in cord, so the cord tolerance printed on them is ±0.006 in. The two readings differ by 0.005 in — a disagreement nearly as large as the whole cord tolerance on the ring.

The data carries no ID tolerance for either ring, and this page prints none. Averaging the two readings would produce a number that neither source gives, and it would look exactly like the other 367 rings in the tables above. Both rings are on the site with their dimensions and their note; only the ± is missing, and it is missing for a stated reason.

Where this stops

  • Gland depth and bore. Neither is in this data, so this page cannot turn a tolerance into a squeeze figure. The tolerance is one input to that calculation, not the answer.
  • Inch only. AS568 is an inch standard and so are these tolerances. The millimetre columns on the ring pages are ×25.4 conversions, not ISO 3601-1 sizes, and this page does not quote either.
  • One series is mixed. The 9-series is a purpose series rather than a cord family: it carries 9 different cord sizes, from 0.056 to 0.118 in, so its own ladder is the shortest in the table.
  • Material. Nothing here says what the ring is made of, and tolerance does not change with compound. Hardness, compression set and temperature range are on the compound pages, summarised in their own article.
  • Which ring to buy. This page compares tolerances. It does not know your groove, and it makes no recommendation.

What a dash number does and does not tell you is covered by its own guide. The series pages carry the full tables — 3-series and 4-series between them account for 9 of the twelve rows above — and every ring is on the site under o-rings.