Materials

48 materials grouped by family — density, corrosion behaviour, and the grades each is commonly supplied in. Density is the number that turns a drawing into a weight.

MetalsSteels, stainless and non-ferrous alloys. Density drives weight; the alloy family drives corrosion behaviour and the property classes available.

Metals database
steel · 7.85 g/cm³Carbon SteelThe default structural fastener material. Low cost, high strength, normally supplied zinc plated or black oxide to slow corrosion.stainless · 7.9 g/cm³Stainless Steel A2 (304)Austenitic 18/8 stainless (AISI 304 family). The general purpose corrosion resistant choice for fasteners.stainless · 8 g/cm³Stainless Steel A4 (316)Austenitic stainless with molybdenum (AISI 316 family). Used in marine and chemical exposure where A2 pits.steel · 7.85 g/cm³Alloy SteelQuenched and tempered alloy steel used to reach property classes 10.9 and 12.9.non-ferrous · 8.5 g/cm³BrassCopper-zinc alloy. Non-magnetic, corrosion resistant, used for electrical terminals and decorative hardware.non-ferrous · 2.7 g/cm³AluminiumWeight critical applications. Roughly one third the weight of steel.non-ferrous · 4.51 g/cm³TitaniumGrade 2 / Grade 5 (Ti-6Al-4V) fasteners for aerospace, motorsport and medical implants.non-ferrous · 2.7 g/cm³Aluminium 6061-T6The default structural aluminium. Heat treatable and easy to machine, so it carries most machined brackets, frames and fixtures. About a third the weight of steel, at about a third of the stiffness.non-ferrous · 2.7 g/cm³Aluminium 6063-T5The extrusion alloy. Made for architectural profiles — window frames, handrails, heat sinks — where surface finish and the ability to extrude thin complex walls matter more than strength.steel · 7.85 g/cm³Carbon Steel A36The structural steel. Bought as plate, bar and shapes for welded and bolted frames rather than for machined parts, and priced accordingly.steel · 7.87 g/cm³Carbon Steel 1018The free-cutting low-carbon steel. Sold as cold-drawn bar for shafts, pins, spindles and studs — parts that are turned, drilled and threaded rather than welded into a structure.

PlasticsNon-metallic materials for insulation, light duty and chemical exposure. Low density, but service temperature and creep set the limits.

Plastics database

RubberElastomers for sealing and damping. Chosen by the media a joint meets before its temperature — and always against a compound, not the family.

Rubber database

CompositesFibre-reinforced laminates. Light and stiff, but directional: every strength figure here is quoted along or across the fibres, never as one number.

Composites database

WoodCommon species with reference density at air-dried moisture content. Weight varies with moisture far more than with any other variable here.

Wood database
wood · 0.75 g/cm³OakRing-porous hardwood, dense and hard wearing. White oak is the traditional choice for barrels, boatbuilding and heavy furniture; red oak is more common in cabinetry and flooring.wood · 0.705 g/cm³Maple (Hard Maple)Dense, fine-grained hardwood with good wear resistance. Hard maple is the usual choice for flooring, butcher blocks and work surfaces where the surface has to take abuse.wood · 0.69 g/cm³Birch (Yellow Birch)Dense hardwood, widely used in plywood and cabinetry. Yellow birch is harder and heavier than paper birch, and is often substituted for maple where the surface is not the point.wood · 0.55 g/cm³Pine (Southern Yellow)Softwood used for structural framing, decking and general building work. Southern yellow pine is a commercial group rather than one species, and its high resin content makes it markedly denser and stronger than eastern white pine.wood · 0.66 g/cm³Walnut (Black)Dark, straight-grained hardwood that machines and finishes exceptionally well. The traditional choice for gunstocks and high-end furniture, and stable enough to hold fine detail.wood · 0.56 g/cm³Cherry (Black)Fine, straight-grained hardwood that darkens with age and light. Works easily by hand, which makes it a common choice for cabinetwork and musical instrument parts.wood · 0.67 g/cm³Ash (White)Strong hardwood with excellent shock resistance — the reason it is used for tool handles, sports equipment and anything that has to absorb a repeated impact rather than resist a steady load.wood · 0.82 g/cm³HickoryAmong the hardest and toughest of the common North American hardwoods. Dense, shock resistant and used wherever a handle has to survive repeated abuse.wood · 0.72 g/cm³Beech (American)Dense, fine-grained hardwood that wears evenly without splintering. The traditional material for workbench tops and butcher blocks, and widely used for flooring and bent furniture parts.wood · 0.42 g/cm³Poplar (Yellow)Light, uniform hardwood that is easy to work and takes paint well. The usual choice for painted cabinetry, interior trim and anything that will not be seen in its natural state.wood · 0.42 g/cm³BasswoodSoft, even-textured hardwood with almost no grain figure. Carves and shapes predictably, which makes it the standard stock for carving, pattern making and scale models.wood · 0.16 g/cm³BalsaThe lightest commercial timber. A hardwood by botany but softer than any softwood here, used for model building, buoyancy and as a core material inside composite sandwich panels.wood · 0.63 g/cm³TeakNaturally oily hardwood with outstanding resistance to water, rot and insects. The reference material for outdoor furniture and boat decking, and priced accordingly.wood · 0.55 g/cm³Mahogany (Honduran)Stable, easily worked hardwood with a warm reddish tone. Long the standard for fine furniture, boat trim and instrument bodies because it moves little once dry.wood · 1 g/cm³IpeExceptionally dense tropical hardwood that sinks in water. Used for decking and boardwalk where a long service life outdoors justifies both the cost and the difficulty of working it.wood · 0.85 g/cm³Rosewood (East Indian)Dense tropical hardwood with a strong figure and high value. Used for instrument backs and sides, inlay work and premium furniture. Trade is restricted under CITES.wood · 0.37 g/cm³Cedar (Western Red)Light, naturally decay-resistant softwood that is dimensionally stable when wet. The default cladding, roofing and outdoor trim material where structure is not carrying the load.wood · 0.47 g/cm³Cedar (Eastern Red)Aromatic, decay-resistant softwood with a fine texture. Traditionally used for chest lining and closet interiors because the oils discourage insects.wood · 0.53 g/cm³Fir (Douglas)Strong, stiff softwood and the standard structural framing timber in North America. Good strength-to-weight, but not decay resistant when left exposed.wood · 0.43 g/cm³Spruce (Sitka)Exceptional stiffness for its very low weight, which is why it is used for aircraft structures and instrument soundboards. A structural softwood with an unusually high strength-to-weight ratio.wood · 0.42 g/cm³RedwoodLight, stable softwood with natural decay resistance. Used for decking, siding and outdoor structures where a long unprotected service life matters more than strength.wood · 0.47 g/cm³Hemlock (Western)Straight-grained structural softwood used for framing, sheathing and interior joinery. Works cleanly but has no natural decay resistance, so it belongs where it will stay dry.wood · 0.58 g/cm³LarchThe densest of the common softwoods, with better natural durability than most conifers. Used for cladding, decking and fence posts where treated timber is not wanted.wood · 0.48 g/cm³Cypress (Bald)Decay-resistant softwood that has been the traditional outdoor and boatbuilding timber of the southern United States. Relatively light for its durability.engineered · 0.68 g/cm³Birch PlywoodCross-laminated veneer sheet with alternating grain direction, which makes it far more dimensionally stable than solid timber. Birch-faced stock is the standard for cabinetwork and jigs.engineered · 0.75 g/cm³MDF (Medium Density Fibreboard)Uniform sheet made from wood fibre bonded with resin. No grain, so it routes and machines identically in every direction and takes paint without a grain raise.engineered · 0.65 g/cm³OSB (Oriented Strand Board)Structural panel built from oriented wood strands bonded with resin. An engineered substitute for plywood in sheathing and flooring, produced from fast-growing species.engineered · 0.7 g/cm³BambooA grass rather than a timber, laminated into boards from strips or strands. Grows to harvest in a few years and gives a hard, stable surface for flooring and worktops.

Lumber sizesthe one dimension question every first build runs into

Lumber size database

A nominal size is not what the board measures. The lumber size database carries both figures for all 18 standard sizes, plus board feet and the weight of each one at each tabulated length across every species here.

Density comparisonall materials on one scale, lightest first

Weight calculator
MaterialFamilyDensity (g/cm³)kg/m³
BalsaWood0.16160
Cedar (Western Red)Wood0.37370
Poplar (Yellow)Wood0.42420
BasswoodWood0.42420
RedwoodWood0.42420
Spruce (Sitka)Wood0.43430
Cedar (Eastern Red)Wood0.47470
Hemlock (Western)Wood0.47470
Cypress (Bald)Wood0.48480
Fir (Douglas)Wood0.53530
Pine (Southern Yellow)Wood0.55550
Mahogany (Honduran)Wood0.55550
Cherry (Black)Wood0.56560
LarchWood0.58580
TeakWood0.63630
OSB (Oriented Strand Board)Wood0.65650
Walnut (Black)Wood0.66660
Ash (White)Wood0.67670
Birch PlywoodWood0.68680
Birch (Yellow Birch)Wood0.69690
BambooWood0.7700
Maple (Hard Maple)Wood0.705705
Beech (American)Wood0.72720
OakWood0.75750
MDF (Medium Density Fibreboard)Wood0.75750
HickoryWood0.82820
Rosewood (East Indian)Wood0.85850
EPDM RubberRubber0.86860
Natural Rubber (NR)Rubber0.93930
Silicone Rubber (VMQ)Rubber0.98980
Nitrile Rubber (NBR)Rubber11000
IpeWood11000
Nylon (PA 6.6)Plastics1.141140
Aramid Fibre Composite (AFRP)Composites1.381380
Carbon Fibre Composite (CFRP)Composites1.61600
Fluoroelastomer (FKM)Rubber1.851850
Glass Fibre Composite (GFRP)Composites2.12100
AluminiumMetals2.72700
Aluminium 6061-T6Metals2.72700
Aluminium 6063-T5Metals2.72700
TitaniumMetals4.514510
Carbon SteelMetals7.857850
Alloy SteelMetals7.857850
Carbon Steel A36Metals7.857850
Carbon Steel 1018Metals7.877870
Stainless Steel A2 (304)Metals7.97900
Stainless Steel A4 (316)Metals88000
BrassMetals8.58500

Each family is quoted at its own reference condition, and the differences matter when comparing across the table. Wood densities are for air-dried stock at about 12% moisture content, the usual engineering reference condition; green timber can be 50% or more heavier. Metal densities are for the alloy at room temperature. Rubber densities are for the unfilled base polymer — production compounds are filled and run higher, above 1.3 g/cm³ for several of them. Composite densities are for a unidirectional laminate at the fibre volume fraction stated on the entry, so they move if the layup does.

Material → property classmetals only — property classes describe heat-treated alloys

All 12 property classes
MaterialDensity (g/cm³)Property classes
Carbon Steel7.85Property Class 4.8, Property Class 5.8, Property Class 8.8, SAE J429 Grade 2, SAE J429 Grade 5
Stainless Steel A2 (304)7.9A2-70 Stainless (304), A2-80 Stainless (304)
Stainless Steel A4 (316)8A4-70 Stainless (316), A4-80 Stainless (316)
Alloy Steel7.85Property Class 10.9, Property Class 12.9, SAE J429 Grade 8
Brass8.5—
Aluminium2.7—
Titanium4.51—
Aluminium 6061-T62.7—
Aluminium 6063-T52.7—
Carbon Steel A367.85—
Carbon Steel 10187.87—

The non-metals are absent from this table on purpose. Property classes describe the heat treatment of alloy steels, and have no meaning for a material that is not heat treated to a tensile class — wood is graded by species, rubber by compound, and a laminate by its fibre volume fraction.

Further familiesplanned, not yet published

PlannedCeramicsAlumina, zirconia and silicon nitride by grade and application.
PlannedFoamsClosed and open cell foams by density, for gaskets and damping.