A DIN 660 rivet is ordered by two numbers: a shank diameter and a length. This database holds 265 of those combinations across two tables — round head and countersunk — and both are built on the same 13 diameters and the same 20 lengths. What the length number means, though, is not the same in the two, and that is where this page starts.
20 rungs, 3 gaps
| Length (mm) | Step to the next (mm) | Diameters, DIN 660 | Diameters, DIN 661 |
|---|---|---|---|
| 2 | 1 | 5 | 4 |
| 3 | 1 | 7 | 5 |
| 4 | 1 | 9 | 6 |
| 5 | 1 | 10 | 8 |
| 6 | 2 | 11 | 8 |
| 8 | 2 | 12 | 8 |
| 10 | 2 | 11 | 8 |
| 12 | 2 | 10 | 8 |
| 14 | 2 | 9 | 7 |
| 16 | 2 | 9 | 7 |
| 18 | 2 | 9 | 6 |
| 20 | 2 | 9 | 5 |
| 22 | 3 | 8 | 4 |
| 25 | 3 | 8 | 4 |
| 28 | 2 | 7 | 3 |
| 30 | 2 | 7 | 3 |
| 32 | 3 | 6 | 2 |
| 35 | 3 | 6 | 2 |
| 38 | 2 | 6 | 1 |
| 40 | — | 6 | 1 |
The ladder runs from 2 to 40 mm and consecutive rungs differ by one of 3 amounts only: 4 steps of 1 mm, 11 steps of 2 mm, 4 steps of 3 mm. That is the whole progression — there is no 1.5 mm step anywhere, and no step of 4.
The three kinds are not mixed evenly. Every rung below 6 mm is 1 mm from the next, so the choice is fine exactly where the rivets are short. Above that there is not one 1 mm step left: the first 3 mm step starts at 22 mm, and between 22 and 25 mm there is nothing at all to order.
A grid that is 63.5% full
| d (mm) | Lengths, DIN 660 | Shortest (mm) | Longest (mm) | Range (mm) | Steps (mm) |
|---|---|---|---|---|---|
| 1 | 5 | 2 | 6 | 4 | 1 |
| 1.2 | 6 | 2 | 8 | 6 | 1, 2 |
| 1.4 | 7 | 2 | 10 | 8 | 1, 2 |
| 1.6 | 8 | 2 | 12 | 10 | 1, 2 |
| 2 | 12 | 2 | 20 | 18 | 1, 2 |
| 2.5 | 13 | 3 | 25 | 22 | 1, 2, 3 |
| 3 | 15 | 3 | 30 | 27 | 1, 2, 3 |
| 3.5 | 18 | 4 | 40 | 36 | 1, 2, 3 |
| 4 | 18 | 4 | 40 | 36 | 1, 2, 3 |
| 5 | 17 | 5 | 40 | 35 | 1, 2, 3 |
| 6 | 16 | 6 | 40 | 34 | 2, 3 |
| 7 | 15 | 8 | 40 | 32 | 2, 3 |
| 8 | 15 | 8 | 40 | 32 | 2, 3 |
13 diameters crossed with 20 lengths would be 260 cells. DIN 660 fills 165 of them, and all 100 cells of DIN 661 are among those 165 — the countersunk table is a strict subset of the round-head table, not a second grid beside it.
Each diameter has its own window, and both ends of the window move with the diameter. The shortest length climbs from 2 mm at the smallest diameter to 8 mm at the largest; the longest climbs from 6 to 40. The window is widest at 3.5 and 4 mm, where it spans 36 mm of length, and narrows again at the top of the range, to 32 mm.
Two edges cut that shape. The floor is the shank itself: every one of the 265 rivets is at least as long as its own diameter, without a single exception, so all 23 cells below the l = d line are empty. The ceiling is the catalogue rather than a rule: 6 of the 13 diameters run all the way to 40 mm and the other 7 stop shorter. That is why the count climbs to 18 lengths at 3.5 and 4 mm and then falls back to 15 at the top of the range, while the smallest diameter here has only 5. Of the 95 empty cells, 23 sit under the floor and 72 above a ceiling.
Read the same table by column and the band appears from the other side: 12 of the 13 diameters stock an 8 mm rivet, 6 stock the 40 mm one, and only 5 stock the 2 mm one.
The same number, measured from two faces
l is not measured from the same place in the two tables. The DIN 661 page states it in its notes: there the length runs from the top face of the head, not from under it, which is the opposite of DIN 660. The offset is therefore the countersunk head's own depth k, and it is a rule rather than a measurement — the round head's height is 0.6 d rounded to 0.1 mm at all 13 diameters, so k over d runs from 0.571 to 0.625 without the geometry doing anything unusual.
| d (mm) | Head height k, DIN 660 | Head depth k, DIN 661 | Widest step at this d | k against that step |
|---|---|---|---|---|
| 1 | 0.6 | 0.5 | 1 | smaller |
| 1.2 | 0.7 | 0.6 | 2 | smaller |
| 1.4 | 0.8 | 0.7 | 2 | smaller |
| 1.6 | 1 | 0.8 | 2 | smaller |
| 2 | 1.2 | 1 | 2 | smaller |
| 2.5 | 1.5 | 1.2 | 3 | smaller |
| 3 | 1.8 | 1.4 | 3 | smaller |
| 3.5 | 2.1 | 1.8 | 3 | smaller |
| 4 | 2.4 | 2 | 3 | smaller |
| 5 | 3 | 2.5 | 3 | smaller |
| 6 | 3.6 | 3 | 3 | equal |
| 7 | 4.2 | 3.5 | 3 | larger |
| 8 | 4.8 | 4 | 3 | larger |
At 8 mm a rivet ordered as 40 mm is 40 mm of shank in DIN 660 and 36 mm of shank in DIN 661: the same order number, 4 mm less metal in the hole.
That offset is not a rounding error against the ladder. At 7 and 8 mm the countersunk depth is larger than the widest step in either ladder — the table above prints both numbers — and at 6 mm the two are equal. Everywhere below that the offset is smaller than a step, which is why the mismatch is invisible on small rivets and worth more than a whole rung on the largest ones.
The hole is a step, not a percentage
| d (mm) | dH12 (mm) | dH12 − d (mm) | Share of d |
|---|---|---|---|
| 1 | 1.05 | 0.05 | 5.00% |
| 1.2 | 1.25 | 0.05 | 4.17% |
| 1.4 | 1.45 | 0.05 | 3.57% |
| 1.6 | 1.65 | 0.05 | 3.12% |
| 2 | 2.1 | 0.1 | 5.00% |
| 2.5 | 2.6 | 0.1 | 4.00% |
| 3 | 3.1 | 0.1 | 3.33% |
| 3.5 | 3.6 | 0.1 | 2.86% |
| 4 | 4.2 | 0.2 | 5.00% |
| 5 | 5.2 | 0.2 | 4.00% |
| 6 | 6.3 | 0.3 | 5.00% |
| 7 | 7.3 | 0.3 | 4.29% |
| 8 | 8.4 | 0.4 | 5.00% |
dH12 − d takes 5 values across the 13 diameters — 0.05, 0.1, 0.2, 0.3, 0.4 mm — so it is a step function, not a percentage: it holds over a run of diameters and jumps at 1, 2, 4, 6 and 8. As a share of the shank the clearance runs from 2.86% at 3.5 mm to 5.00% at 1, 2, 4, 6 and 8 mm.
Those 5.00% rows are exactly the sizes where the clearance steps up, so the loosest fit in relative terms is at the sizes that get used most, and the tightest is at 3.5 mm — one of the diameters the DIN 660 page names as non-preferred.
The mass column is one density
Mass is the other column that is arithmetic. Fit the steel column of one diameter against length and the slope is the shank's own area times a density: at 8 mm it rises 0.394578 g per millimetre, and 0.394578 / (π/4 × 8²) = 7.850 g/cm³.
Every diameter from 2 mm up returns that same figure to within 0.002 g/cm³, and the stainless column returns 7.900 — a ratio of 1.0064. The two columns are one volume multiplied by two densities, not 265 weighings, and 28 of the 265 rows print the same number twice because at those sizes the difference is below the third decimal. Below 2 mm the same fit stops working, and not because the metal changes: the column is printed to 0.001 g and the slope of a 1 mm rivet is smaller than that step.
Where this stops
- Grip. There is no clamp-thickness column in this data, and the standard's own grip table is not in it either, so this page cannot turn a length into a joint thickness. It compares the ladders; it does not choose a length for your stack.
- Head strength. k and d2 are here, the head's volume is not, and no shear or bearing value is in this database. A longer rivet does not carry more load — it carries the same load over a thicker stack, and that is a different question.
- Tolerance on l. Every length here is nominal; nothing in this data says how much a delivered rivet may vary, and at the bottom of the ladder one step is only 1 mm.
- Which head. That depends on the sheet, not on this table: a countersunk head needs a matched countersink, and the DIN 661 page covers the 75° angle and what a 90° countersink does to a flush finish.
- Which rivet to buy. This page compares two tables. It does not know your joint.
Every rivet in both tables is on the site as a page — the rivets index lists them by standard, and the fastener library is the way in to the rest.