A bearing designation answers three questions with three numbers. The bore is the shaft, the outside diameter is the hole, the width is the space along the shaft. Only one of the three is ever free.

Two numbers, two constraints

In a repair the mounting bore already exists — it is a dimension measured off a housing, and it puts a hard cap on the outside diameter. The shaft is a measurement too. The two arrive independently, and the bearing has to satisfy both at once.

The dimensions series sits between them. It is not a size and not a quality grade. It is how much bearing gets built into the space between a given shaft and a given hole.

So neither number identifies a bearing on its own. Across the 213 deep groove ball bearings here — 8 series, all ISO 15 — there are 72 distinct outside diameters, and 51 of them (70.8%) carry more than one bore. The busiest one takes 7 different shafts.

One outside diameter, 7 bores

DesignationSeriesBore (mm)Outside diameter (mm)Width (mm)Radial section (mm)
61718617901101010.0
61817618851101312.5
61916619801101615.0
16014160701101320.0
601460701102020.0
621262601102225.0
631063501102730.0
640864401102735.0

All 8 rows fit the same 110 mm housing bore. The shafts run from 40 to 90 mm, a factor of 2.25, and the widths from 10 to 27 mm.

Put the two ends side by side. 61718 takes a 90 mm shaft in 10 mm of width; 6408 takes a 40 mm shaft in 27 mm of width. Same housing, same outside diameter — and the radial section runs the other way: 35.0 mm on the thinner shaft against 10.0 mm on the thicker one. In this table it never rises as the bore grows, and that is the whole trade.

That is the trade the series makes. More radial section means thicker rings and larger rolling elements between the same two diameters, so the bearing carries more. This database puts no number on "more": load ratings are catalogue values that differ between makers for the same designation, so they are absent rather than averaged.

Same bore, same outside diameter, different width

Two rows in that table are not two sizes. 6014 and 16014 share the bore (70 mm), share the outside diameter (110 mm), and differ only in width: 20 mm against 13 mm, 7 mm apart.

That is the width series. Across this library 21 bores have exactly this shape — one outside diameter, one bore, two widths:

Bore (mm)Outside diameter (mm)60 width (mm)160 width (mm)Difference (mm)
1026871
1228871
1532981
17351082
20421284
25471284
30551394
35621495
40681596
457516106
508016106
559018117
609518117
6510018117
7011020137
7511520137
8012522148
8513022148
9014024168
9514524168
10015024168

Every one of those 21 pairs is the same two series, 60 and 160, and in every pair the outside diameters are identical. That is where the trade name Narrow comes from: it is narrow, not small. A 160 bearing has the same outside diameter as the 60 of the same bore and gives up between 11.1% and 40.0% of its width.

The difference is smallest at the small end and never falls back: 1 mm at the top of the table, 8 mm at the bottom, and no row in between where it shrinks.

What the series names measure

SeriesTrade nameRecordsBore (mm)Outside diameter (mm)Radial section (mm)
617Extra-thin2110–10015–1202.5–10.0
618Ultra-thin2110–10019–1254.5–12.5
619Thin2110–10022–1406.0–20.0
60Extra-light3710–30026–4608.0–80.0
160Narrow2110–10026–1508.0–25.0
62Light3710–30030–54010.0–120.0
63Medium3710–30035–62012.5–160.0
64Heavy1817–10062–25022.5–75.0

Read the last column rather than the outside diameter. The trade names run in order of radial section, from Extra-thin at 2.5 mm to Heavy at 22.5 mm, both at their smallest bore. "Extra-light" and "Heavy" describe how much material sits between the two diameters, not how big the bearing is.

Two series can share a radial section, share an outside diameter, and still be different bearings. 60 and 160 both start at 8.0 mm of section and take the same bores; the only thing separating them is width.

Choosing in the order the constraints arrive

  1. Measure the housing bore. That is an outside diameter and a hard cap — it eliminates most of the 72 values above before the shaft is even mentioned.
  2. Measure the axial space. That is a width cap.
  3. Measure the shaft. Usually one or two rows are left.
  4. When two rows survive with the same bore and the same outside diameter, the narrower one wins if axial space is what ran out. What you give up is load capacity and life, and neither is tabulated here.
  5. If nothing survives all three, change the machine. No bearing in a series is thinner than that series.

The commonest mistake runs the list backwards: choose by shaft, then find the housing has to be bored out. The bearing index lists all 213 with their boundary dimensions, and each series page prints its whole bore range.

What is not on this page

  • Load ratings, limiting speeds and mass are catalogue figures that differ between makers for the same designation, so they are absent rather than averaged into something that looks authoritative.
  • Tolerance class and sealing are suffixes on the designation — separate decisions that this database does not encode. Clearance is a suffix too, but it is encoded, and it turns out to be a range rather than a number.
  • Only boundary dimensions are compared: bore, outside diameter, width, and the radial section derived from the first two. Those are the values ISO 15 fixes.
  • Only the 8 deep groove ball series are counted above. Tapered roller, cylindrical roller, needle and thrust bearings have their own series and their own standards; mixing them into one "bores per outside diameter" figure would be a number about nothing.

Every bearing page names the standard its dimensions come from, and the standards index says which standard fixes which dimension.