A screw is ordered by two numbers, and the length is not a measurement you can ask for in any value you like. It is a rung. This database holds 1,998 metric screws and bolts, and they occupy 23 lengths in total — from 3 mm to 200 mm, with nothing in between that is not one of those 23 numbers.

1,998 rows, 23 lengths, 16 diameters

The 1,998 rows run from M2 to M24, and every one of them sits on the same ladder. There is no M6 × 7 and no M10 × 45, because 7 and 45 are not rungs. That is not a gap in this catalogue: the same ladder turns up in DIN 912, ISO 4017 and every other metric standard here, and the numbers repeat across all of them.

The ladder, with the number of diameters that reach each rung:

Length (mm)DiametersRows
318
4432
5548
6778
8898
109124
1210146
1611168
2011168
2511170
3012168
351096
4012164
5012148
6012118
701240
801290
1001070
120932
140714
160510
18036
20012

Each step size owns one band

Two adjacent rungs are 1 mm apart at the bottom and 20 mm apart at the top, and in between the gap only takes 6 values in the whole ladder. Each of them is used in one continuous stretch and then never again:

Step (mm)From (mm)To (mm)Times
1363
26123
412202
520404
1040804
20802006

Read the bands and the ladder stops looking arbitrary. Up to 6 mm it is counted in 1 mm steps; from 6 to 12 in 2 mm; from 12 to 20 in 4; from 20 to 40 in 5; from 40 to 80 in 10; and above 80 in 20. The 6 bands tile the whole ladder — the first starts at 3, the last ends at 200, and each one ends exactly where the next begins.

The consequence is a step that is roughly proportional rather than fixed. Measured against the length you already have, the smallest step in the ladder is 11.1% and the largest is 33.3%: every rung is between one ninth and one third longer than the one below it. 1 mm at the bottom is 33.3% on a 3 mm screw; the same arithmetic at the top gives 11.1% for 20 mm.

Half of the grid is not for sale

16 diameters by 23 lengths is 368 combinations. The database contains 194 of them — 52.7%. The missing ones are not scattered: they are the two ends of the shape. The 6 rungs at 30, 40, 50, 60, 70 and 80 mm are each reached by 12 of the 16 diameters, while the shortest rung, 3 mm, exists for exactly 1 diameter, and the longest, 200 mm, for exactly 1 — M24, in 2 rows.

The busiest single rung is 25 mm, with 170 rows across 11 diameters — more rows than any other rung, and a diameter count within one of the widest.

The shortest length is the diameter itself

For 8 of the 16 diameters the shortest screw on the ladder is exactly as long as it is wide — M3 × 3, M4 × 4, M5 × 5, M6 × 6, M8 × 8, M10 × 10, M12 × 12 and M16 × 16. A shorter cap screw would be a head and nothing to hold.

Above that the two ends of each diameter's range diverge, and this is where the ladder stops being symmetric:

d (mm)Shortest (mm)Longest (mm)Longest ÷ dLengths
242010.08
2.542510.09
333010.011
3.56308.68
448020.016
558016.015
6610016.715
8812015.015
101012012.014
121214011.714
142514010.011
161616010.014
18301608.911
20301809.012
22401808.210
24402008.311

The longest screw shrinks as the screw grows

The fourth column is the one worth reading twice. M4 can be ordered at 80 mm — 20.0 times its own diameter. M22 stops at 180 mm, which is 8.2 times its diameter. A thick screw cannot be bought slender in the way a thin one can, and no amount of shopping changes that: the ladder simply does not have those rungs.

The same table read downward explains the other end. Every diameter has between 8 and 16 of the 23 lengths available, so a bill of materials written around one diameter rarely transfers to the next size up without a change.

What to do with a ladder instead of a scale

  • Do not assume a 5 mm step. It holds between 20 and 40 mm and nowhere else; below that the ladder is finer, above it coarser.
  • Work out the clamp length first, then take the next rung up. What you gain is between 11.1% and 33.3% of the screw you were looking at — not a fixed allowance.
  • When a joint needs an unusually long screw, check the diameter before the length: the ladder stops at 200 mm in every diameter, and only M24 reaches it. If that is not enough, the answer is the unthreaded shank or the thread length on a different family, not a longer rung.
  • The inch tables are a separate ladder again, counted in fractions rather than millimetres, so a length read off one does not transfer to the other.