A wood screw is called out as 8 × 80, and both numbers behave differently from the same-looking numbers on a machine screw. The first is not a thread designation and the second is not a rung on a ladder — and the standard's own table is what says so.

The first number is a shank

On a machine screw the size in front of the × names a thread: a crest diameter, with a pitch that follows from a table. On a DIN 571 wood screw the 8 names the largest the shank gets — the column is printed as ds max., 8 mm on this screw, and the shank is allowed to come down to 7.42 mm. Across the 9 columns that band is between 0.48 and 0.7 mm wide.

A band that loose is normal for a rolled wood thread and would be unthinkable on a machine screw, and it follows from what the thread does: it is a DIN 7998 wood thread, coarse and tapered to a point, cutting its own way into the timber. Nothing is preloaded, nothing is mated. There is no pitch to quote, no tap drill to look up and no nut to buy. The page for each size says as much, and stops there rather than inventing a drilling rule — the pilot hole depends on species and moisture content, which no fastener standard governs.

Nine columns, eight that you can buy

The standard's dimension table prints 9 diameters. The mass table that decides which lengths exist has entries under 8 of them.

d (mm)ds max. (mm)s (mm)k (mm)LengthsShortest (mm)Longest (mm)Longest ÷ d
4472.86164010
5583.58165010
6610411208013.33
77125————
88135.5142510012.5
1010177133010010
1212198143512010
16162410155016010
20203013176020010

The 7 mm column is fully dimensioned — shank 7, width across flats 12, head height 5 — and carries no length at all. That is why the wood screw category lists 8 groups while the standard page prints 9 rows. Neither page is wrong; they are reporting two different tables.

Why 7 mm has no products is not in either table, and this page will not guess. What it will say is what the two tables show: a column exists, and nothing is listed under it. If a 7 mm screw is in the catalogue you are holding, it is not in this standard's table, and its dimensions would be worth checking against these before ordering.

The length list is a product list

The heading of the mass table calls its rows commercial items, and that is the whole explanation for the shape of the length lists. A ladder would run from a minimum to a maximum in equal steps. This one does not:

  • 26 lengths in total, from 16 to 200 mm.
  • The step changes: 4 mm once, 5 mm 12 times and 10 mm 12 times, with the 5 mm run ending at 80 mm.
  • Each column stops where its own products stop. The shortest screw in the 4 mm column is 16 mm; in the 20 mm column it is 60 mm.
  • No length is offered in all 8 columns. The busiest are 35, 40, 50, 60, 70 and 80 mm at 6 columns each, and 170, 180, 190 and 200 mm are made in one diameter only.

Read the other way, the list has a hole in it. The 6 mm column offers 11 of the 13 lengths between 20 and 80 mm, skipping 65 and 75 mm. There are lengths on both sides of that hole — 60 mm below it and 80 mm above — so this is not a column that simply ends early.

That is the practical difference between this family and the machine screw length ladder. There the question is "how far apart are the steps"; here it is "was this combination ever made", and the only answer is the table.

Ten diameters long, except where the table says otherwise

The longest screw in each column, divided by the diameter, is a tidy 10 in 6 of the 8 columns. The exceptions are 6 mm at 80 (13.33 diameters) and 8 mm at 100 (12.5 diameters).

At the bottom end there is no such neatness: the shortest screw is between 2.92 and 4 diameters long depending on the column. So a rule of thumb taken from the top of the table — the longest screw is 10 diameters — predicts a 60 mm ceiling on the 6 mm column, and the table goes to 80 mm. That is the kind of sentence this family punishes.

The mass column is a straight line

The mass is printed for every length, so it can be checked against the lengths rather than trusted. Fit a line through each column's printed masses and the departure is at most 1.31% of that column's heaviest screw:

d (mm)Mass per mm (g)Head (g)Head share of the shortestLargest residual
40.0750.5330.8%1.21%
50.1200.9934.1%1.26%
60.1541.9939.6%0.48%
80.2734.6140.1%0.65%
100.43410.4744.4%0.61%
120.63113.8638.3%0.35%
161.14226.5931.6%0.63%
201.83854.1132.8%1.31%

The slope is the part of the screw that grows with length, and read as a solid cylinder of the same density it comes out at 83%–88% of the nominal diameter — between the thread root and the crest, which is exactly where the average section of a tapered, threaded shank sits. The intercept is the part that does not grow: the head, from 0.53 g on the 4 mm column to 54.11 g on the 20 mm one.

That intercept is not a rounding artefact. On the shortest screw in each column it is between 30.8% and 44.4% of the total mass: a 4 × 16 weighs 1.71 g, and 30.8% of that is head. Two consequences worth carrying:

  • The head is a large share of a short screw. Comparing two short lengths by mass per millimetre overstates the difference, because the fixed head dilutes it.
  • Mass scales as length, not as length cubed. A 20 × 200 weighs 421 g, so a thousand of them weigh 421 kg — which is the number a shipping quote actually needs.

What the table does not settle

  • The pilot hole. Not in the standard, and not derivable from it: species and moisture content decide. The size pages say so instead of quoting a drill.
  • Embedment, spacing and edge distance. Timber connection design, not a fastener dimension table. A screw that is right for the hole can still be wrong for the joint.
  • Where the length starts. On the pages here l runs from the bearing face of the head to the point, the same datum as a hex bolt. A supplier who quotes over the head gives a number that is k shorter for the same screw — between 2.8 and 13 mm across these columns, which is not a rounding difference on a short screw.
  • Grade and coating. The dimension table prints no property class, because a wood screw has none the way a bolt has 8.8. Whatever class a box is labelled with describes the wire it was drawn from, not a clamping force — nothing here is preloaded. Coating is a supplier option and not part of the table.
  • How much your screw weighs. The printed mass is an approximate figure at ρ = 7.85 kg/dm³ for commercial items, not a weighing of the part in your hand.

Where to start

The wood screw category groups all 98 sizes by diameter, and the DIN 571 standard page prints the 9 dimension rows including the one with no products. For a single size, 20 × 200 shows the dimension row, the mass and the head geometry together — which is where the two-number callout finally turns into a drawing.