6314 Deep Groove Ball Bearing
6314 is a single-row deep groove ball bearing, medium series, with a 70 mm bore, a 150 mm outside diameter and a 35 mm width. Those four numbers — bore, outside diameter, width and the 2.1 mm minimum chamfer — are ISO 15 standard values, identical for every manufacturer.
Dimensions
All 6300 Series designations- Designation
- 6314
- Type
- Single-row deep groove ball bearing
- Series
- 6300 Series (medium)
- Bore code
- 14 — 70 mm
- Bore d
- 70 mm (2.7559 in)
- Outside diameter D
- 150 mm
- Width B
- 35 mm
- Chamfer, r s min
- 2.1 mm — minimum, not nominal
- Radial section
- 40 mm = (D − d) / 2
Nominal values in millimetres as published in ISO 15, the boundary dimension plan for radial bearings. The chamfer figure is the minimum single chamfer dimension the plan gives (r s min); the matching maximum is in ISO 582 — which is why the row says “min” and not an equality. A bearing that has been fitted with shields or seals carries the same four dimensions, because none of the suffixes touches the boundary dimension plan.
Reading the designationwhere 70 mm comes from
The designation is three fields: type, diameter series and bore code. For codes 04 and above the bore is the code multiplied by five, which is why 14 gives 70 mm. The four exceptions are 00, 01, 02 and 03 at 10, 12, 15 and 17 mm.
Position in the series15 of 21 in 6300 Series
Radial internal clearanceISO 5753-1, bore 65–80 mm
| Group | Radial internal clearance | When it is used |
|---|---|---|
| C2 | 1–15 µm | Tighter than default; for fits that already take up the clearance. |
| CN (normal) | 10–30 µm | The default — usually not marked on the bearing at all. |
| C3 | 25–51 µm | Interference fits, electric motors, hot inner ring. The common upgrade. |
| C4 | 46–71 µm | Heavy interference fits and high-temperature service. |
| C5 | 65–105 µm | The loosest group in the table; special applications. |
Values are the pre-mounting radial internal clearance for a deep groove ball bearing with a cylindrical bore, in micrometres, from ISO 5753-1. Pressing the inner ring onto a shaft and running the inner ring hotter than the outer ring both close this up — an interference of a few micrometres is a few micrometres straight out of the running clearance, which is the whole reason C3 exists. For this bore, normal (CN) is 10–30 µm and C3 is 25–51 µm.
What is deliberately not publishedwhy there is no load rating here
No load rating, no limiting speed and no mass appears on this page. Those are catalogue values rather than standard values: ISO 281 defines how a dynamic rating is calculated, not what it comes out as, and the result depends on internal geometry — ball diameter, ball complement, raceway conformity — that ISO 15 does not fix. Published catalogue figures for one and the same designation differ between makes by several percent at these sizes, and limiting speed additionally depends on lubrication and on whether the bearing is open, shielded or sealed. Publishing any single figure here would dress a catalogue entry up as a property of the designation. Take the rating from the catalogue of the bearing you actually buy.
The dimensions above are a different matter, and they are the reason a designation is worth anything: bore, outside diameter, width and the chamfer minimum are fixed by ISO 15, so every maker's bearing of this designation fits the same shaft and the same housing.
Same bore, other serieswhat the 70 mm shaft would take instead
| Designation | Series | D | B | Section (D − d)/2 | vs 6314 |
|---|---|---|---|---|---|
| 6314 | Medium — this bearing | 150 | 35 | 40 | — |
| 6014 | 6000 Series — Extra-light | 110 | 20 | 20 | -40 mm on D |
| 6214 | 6200 Series — Light | 125 | 24 | 27.5 | -25 mm on D |
Three series, one bore: the shaft diameter is the same in every row, so the only thing that changes is what the housing and the axial space have to accommodate. Outside diameter and width are ISO 15 standard values; the section column is derived as (D − d) / 2. Load capacity rises with the outside diameter, but the figure itself has to come from the manufacturer’s catalogue for the bearing you actually buy — see above.