DIN 7981 Cross Recessed Pan Head Tapping Screw
A pan head screw with a cross recess and a thread that cuts its own way into sheet metal, plastic or softwood — there is no nut and no pre-cut thread. The head is the reason to pick it over a countersunk tapping screw: its bearing face is flat and sits on top of the panel, spreading the clamp load instead of wedging into the hole, which is what you want on thin sheet and on anything that will be taken apart again. Nominal sizes run ST2.2 to ST6.3, and the standard prints a mass for every commercial size, so the length lists differ from diameter to diameter rather than running as one block. Two readings of the table catch people out: the head height is a tolerance band (k max and k min), and ST3.9 is a size in its own right, not a variant of ST3.5 — its pitch is 1.4 where ST3.5 is 1.3.
Where it is used
DIN 7981 is a pan head screw with a cross recess and a thread that cuts its own way into sheet metal, plastic or softwood. There is no nut and no pre-cut thread: the screw forms the thread as it goes in, and the material it displaced is what holds it. The pan head is the reason to choose it over the countersunk pattern: its bearing face is flat and sits on top of the panel, spreading the clamp load over a washer-like area instead of wedging into the hole, which is what thin sheet and anything that will be taken apart again needs.
How to choose it
Pick the size from the thickness of the panel and the length from that thickness plus the engagement into whatever is behind it; the thread has to reach through the panel and bite into the second layer, not stop inside the joint. The recess number in the table is the driver size, not a dimension of the screw — H1, H2 and H3 are different bits, and using the next size up is what rounds a cross recess out. There is no property class on these screws and none in this standard: they are surface-hardened so the point can cut, and what the driver has to survive is the driving torque rather than a preload. The hole to drill is not given here, because it depends on the panel material and its thickness, not on the screw.
Dimensions8 sizes · millimetres
| Thread size ST (mm) | Pitch P (mm) | Head diameter dk max. (mm) | Head diameter dk min. (mm) | Head height k max. (mm) | Head height k min. (mm) | Cross recess no. | Type H m ref. (mm) |
|---|---|---|---|---|---|---|---|
| ST2.2 | 0.8 | 4.2 | 3.9 | 1.8 | 1.55 | 1 | 2.6 |
| ST2.9 | 1.1 | 5.6 | 5.3 | 2.2 | 1.95 | 1 | 3 |
| ST3.5 | 1.3 | 6.9 | 6.54 | 2.6 | 2.35 | 2 | 4.2 |
| ST3.9 | 1.4 | 7.5 | 7.14 | 2.8 | 2.55 | 2 | 4.4 |
| ST4.2 | 1.4 | 8.2 | 7.84 | 3.05 | 2.75 | 2 | 4.6 |
| ST4.8 | 1.6 | 9.5 | 9.14 | 3.55 | 3.25 | 2 | 5 |
| ST5.5 | 1.8 | 10.8 | 10.37 | 3.95 | 3.65 | 3 | 6.5 |
| ST6.3 | 1.8 | 12.5 | 12.07 | 4.55 | 4.25 | 3 | 7.1 |
Nominal dimensions in millimetres as published in DIN 7981. Tolerances, material requirements and marking are defined separately by the issuing body.
Available sizeslinked to individual specification pages
Fitting and interchange notes
DIN 7981 was withdrawn in August 1990 and replaced by DIN EN ISO 7049. The two agree cell for cell in every column reproduced on this page — a second source printing the ISO 7049 table was consulted and matched — but equivalence between national standards is dimensional and not metallurgical, so the mechanical requirements come from the wire document (ISO 2702 for steel) rather than from this table. The head height here is a tolerance band, k max and k min, and the head diameter likewise has an upper and a lower limit; both limits are printed because a pan head that is undersize still looks right on a page and wrong in a counterbore. The length lists follow the mass table, which the standard titles as its commercial sizes, so they differ from one diameter to the next instead of running as one block; its 45 and 50 mm rows are empty, which is why no page is generated at those lengths. One printed mass is not repeated anywhere on this site: 4.2 x 32 is listed as 2.84 kg per 1,000 here, while the ISO 7049 table of the second source prints 2.83 — both are consistent with the rest of their own table, so the disagreement is recorded rather than resolved by picking the tidier number. The standard also tabulates the point length for two thread forms, C and F, along with a set of gauge dimensions; those columns are not reproduced here, and nothing on this page is drawn from them.