DIN 7982 Cross Recessed Countersunk Head Tapping Screw
The countersunk version of DIN 7981: same self-tapping thread, same cross recess, but the head is a cone so that it finishes flush with the panel. That is what makes it the screw for anything that has to slide over the joint — hinges, drawer runners, sheet-metal covers, floor plates — and it is also what limits it, because a countersunk head centres itself in the hole and pulls the panel down as it seats, so it will dimple thin sheet if the hole is not countersunk to match. Nominal sizes run ST2.2 to ST6.3. Note what the table does not give: the head height is a single approximate value rather than a tolerance band, and there is no head angle column, so the countersink angle has to come from the mating part rather than from this standard.
Where it is used
DIN 7982 is the countersunk version of the same screw: the same self-tapping thread and cross recess, with the head turned into a cone so that it finishes flush with the panel. That single change is what it is chosen for — hinges, drawer runners, sheet-metal covers, floor plates and anything that has to slide over the joint — and it is also what limits it, because a countersunk head centres itself in the hole and pulls the panel down as it seats. On thin sheet that is useful when the hole is countersunk to match and damaging when it is not: the head will dimple the panel instead of seating in it.
How to choose it
The countersink, not the screw, decides how deep the head sits, so the mating hole has to be cut to the head — and this standard does not give the included angle of that cone, only the head diameter and depth. Sizes are chosen the same way as DIN 7981: the thread has to pass through the panel and bite into what is behind it. There is no property class here either, and no hole size, for the same reasons. One difference from the pan head version is worth flagging before ordering: the length of a countersunk screw is measured from the top face of the head, not from under it, so the same nominal length in the two patterns does not put the same amount of thread into the joint.
Dimensions8 sizes · millimetres
| Thread size ST (mm) | Pitch P (mm) | Head diameter dk max. (mm) | Head diameter dk min. (mm) | Head depth k approx. (mm) | Cross recess no. | Type H m ref. (mm) |
|---|---|---|---|---|---|---|
| ST2.2 | 0.8 | 4.3 | 4 | 1.3 | 1 | 2.5 |
| ST2.9 | 1.1 | 5.5 | 5.2 | 1.7 | 1 | 3 |
| ST3.5 | 1.3 | 6.8 | 6.44 | 2.1 | 2 | 4.2 |
| ST3.9 | 1.3 | 7.5 | 7.14 | 2.3 | 2 | 4.6 |
| ST4.2 | 1.4 | 8.1 | 7.74 | 2.5 | 2 | 4.7 |
| ST4.8 | 1.6 | 9.5 | 9.14 | 3 | 2 | 5.1 |
| ST5.5 | 1.8 | 10.8 | 10.37 | 3.4 | 3 | 6.8 |
| ST6.3 | 1.8 | 12.4 | 11.97 | 3.8 | 3 | 7.1 |
Nominal dimensions in millimetres as published in DIN 7982. Tolerances, material requirements and marking are defined separately by the issuing body.
Available sizeslinked to individual specification pages
Fitting and interchange notes
DIN 7982 was withdrawn in August 1990 and replaced by DIN EN ISO 7050; in the columns reproduced on this page the two agree cell for cell, checked against a second source printing the ISO 7050 table. The head depth k is a single approximate value here, not a tolerance band as on the pan head version, and the column label says so. The mass table heads two extra columns, ST 8 and ST 9.5, which are empty throughout, while the dimension table stops at ST 6.3 — so no page is generated for those two sizes: inventing their head dimensions would be worse than omitting them. The 3.9 mm row of the dimension table has two empty cells of its own, in the point-length columns, and those columns are not reproduced here. The length lists follow the commercial-size mass table, which is why they differ from diameter to diameter rather than running as one block.