DINwood-screwsSlotted round head

DIN 96 Slotted Round Head Wood Screw

The plain wood screw most people mean by the word: a round head with a single slot, a coarse wood thread and a tapered point, turned in with a flat-blade screwdriver. It is the pattern behind almost every hinge, catch, bracket and drawer runner fixed into timber, because the round head sits proud of the surface and spreads its load over a small washer-like face instead of digging in. The slot is why it is not a structural fastener: a driver can only apply as much torque as the slot will take before it cams out, which on the smaller sizes is very little. Nominal diameters run from 1.6 to 8 mm. Two things about the table are worth knowing before reading it: the 1.6 and 5.5 mm columns come from the 2016 edition of the dimension table (the second source consulted prints 2 to 8 mm, identical on every one of those ten diameters), and the mass table marks several diameters as commercial sizes with the letter X instead of a mass — a size that is made, but whose weight the standard does not print.

Dimensioned drawing — DIN 96 4.5 × 18⌀dk 9k 3.1n 1 · t 2⌀ds 4.5l 18
DIN 96 4.5 × 18 — Slotted round headNominal dimensions in mm · Not to scale

Where it is used

DIN 96 is the plain slotted wood screw: a round head with a single slot, the coarse DIN 7998 wood thread and a tapered point, turned in with a flat-blade screwdriver. It is not a machine screw and it is not a self-drilling screw — it has no drill point and no machine thread, so it needs either a pilot hole or a softwood that will let the point start. The round head stays proud of the surface and bears on a small washer-like face, which is why it is the default for hinges, catches, hasps, brackets and drawer runners: the head spreads the load and does not sink into the timber the way a countersunk head does.

How to choose it

Pick the diameter from the thickness of the piece being fixed and the length as the sum of that thickness plus the bite into the piece behind it; the threaded portion has to sit in the second piece, not in the joint. Two limits come with the slotted head and neither is in the table: the slot is the torque limit, because a driver cams out of it long before a hexagon would round off, and the slot also limits how small the smallest sizes can be made useful. There is no strength class here — a wood screw has no property class the way a bolt has 8.8, so capacity comes from the timber design rules, not from this table. Whether a pilot hole is needed depends on species, moisture content and diameter; the standard does not say, and this database does not invent a hole size.

Dimensions12 sizes · millimetres

Thread d1 max. = nom. (mm)Head diameter dk (mm)Head height k (mm)Slot width n (mm)Slot depth t max. (mm)Slot depth t min. (mm)
1.63.21.10.40.70.55
241.40.50.90.7
2.551.70.61.10.85
362.10.81.351.05
3.572.40.81.61.2
482.811.81.4
4.593.1121.55
5103.51.22.31.75
5.5113.81.22.51.9
6124.21.62.72.1
7144.923.22.45
8165.623.62.8

Nominal dimensions in millimetres as published in DIN 96. Tolerances, material requirements and marking are defined separately by the issuing body.

Available sizeslinked to individual specification pages

Fitting and interchange notes

The length listed for each diameter is a length the standard prints a mass for, or one it marks with an X as a commercial size, so the lists differ from one diameter to the next rather than running as one block. An X means the size is made but the mass table gives no figure for it: those pages carry the dimensions and no mass, and the note on the page says so instead of leaving a blank. One printed figure is not repeated anywhere on this site — 2 × 12 is listed as 0.305 kg per 1,000 against 0.311 for the shorter 2 × 10, and a longer screw of the same diameter cannot be lighter; the cell is recorded as unusable rather than corrected, because this database does not edit the standard. The nominal diameter printed here is the outside diameter of the thread, which the table gives as its maximum; it is not a metric size and carries no metric pitch. The 1.6 and 5.5 mm columns come from the 2016 edition of the dimension table.