DIN 97 Slotted Countersunk Head Wood Screw
The same wood screw as DIN 96 with the head turned into a cone, so that it finishes flush with the timber instead of standing proud of it. That single change is why this is the pattern for floorboards, decking, stair treads and anything that has to be walked on or slid over: nothing catches on the head. It pays for that in holding power, because a countersunk head bears on the cone rather than on a flat face, and in timber it will pull itself into the wood until the cone bottoms out — which is why the countersink, not the screw, decides how deep it sits. Nominal diameters run from 1.6 to 10 mm. Note what the table does not give: there is no head angle column and no mass for several diameters, which the standard marks X as commercial sizes.
Where it is used
DIN 97 is the same wood screw with the head turned into a cone so that it finishes flush with the timber. That one change decides where it is used: floorboards, decking, stair treads, cladding and anything that will be walked on or slid over, because there is no head to catch on. It is used the same way as DIN 96 — coarse DIN 7998 wood thread, tapered point, driven with a flat-blade screwdriver — and it is likewise neither a machine screw nor a self-drilling one.
How to choose it
The countersink, not the screw, decides how deep the head sits: in timber the cone pulls itself in until it bottoms out on the wood it has compressed, so a head that stands proud is a countersink that was too shallow, and one that sinks below the surface has crushed the fibres around it and lost most of its hold. That is the trade against DIN 96 — a flush head bears on a cone instead of a flat face. Diameter and length are chosen the same way: the threaded part has to bite into the piece behind the joint, not into the joint itself. There is no strength class in the table and no pilot hole size, for the same reasons as the other wood screws: the first does not exist for wood screws and the second depends on the species and its moisture content.
Dimensions13 sizes · millimetres
| Thread d1 max. = nom. (mm) | Head diameter D (mm) | Head depth k max. (mm) | Slot width n (mm) | Slot depth t max. (mm) | Slot depth t min. (mm) |
|---|---|---|---|---|---|
| 1.6 | 3 | 0.96 | 0.4 | 0.45 | 0.32 |
| 2 | 3.8 | 1.2 | 0.5 | 0.6 | 0.4 |
| 2.5 | 4.7 | 1.5 | 0.6 | 0.7 | 0.5 |
| 3 | 5.6 | 1.65 | 0.8 | 0.85 | 0.6 |
| 3.5 | 6.5 | 1.93 | 0.8 | 1 | 0.7 |
| 4 | 7.5 | 2.2 | 1 | 1.1 | 0.8 |
| 4.5 | 8.3 | 2.35 | 1 | 1.2 | 0.9 |
| 5 | 9.2 | 2.5 | 1.2 | 1.3 | 1 |
| 5.5 | 10.2 | 2.75 | 1.2 | 1.4 | 1.1 |
| 6 | 11 | 3 | 1.6 | 1.6 | 1.2 |
| 7 | 12.5 | 3.5 | 2 | 1.9 | 1.4 |
| 8 | 14.5 | 4 | 2 | 2.1 | 1.6 |
| 10 | 18 | 5 | 2.5 | 2.6 | 2 |
Nominal dimensions in millimetres as published in DIN 97. Tolerances, material requirements and marking are defined separately by the issuing body.
Available sizeslinked to individual specification pages
Fitting and interchange notes
This standard's dimension table has no head angle column: it gives the head diameter and the head depth, not the included angle of the cone, so no angle is printed on these pages — quoting 90° here would be quoting a number the standard does not state. The length lists follow the mass table, which marks several diameters with an X as commercial sizes whose mass it does not print; those pages carry dimensions and no mass, and say so. One figure in that table is not repeated anywhere on this site — 3.5 × 18 is listed as 1.889 kg per 1,000, which is heavier than the same length one diameter up (4 × 18 at 1.64) and heavier than the same diameter one length up (3.5 × 20 at 1.43), so the cell is recorded as unusable rather than corrected. The nominal diameter is the outside diameter of the thread, which the table gives as its maximum, and it carries no metric pitch.