A flat washer carries three numbers: a bore, an outside diameter and a thickness. The thickness is the one most often read backwards. It looks like a proportion of the bolt — twice the bolt, twice the washer — and one row per size does nothing to discourage that reading.

The table is not built that way. The 13 metric sizes in the ISO 7089 table take 8 thicknesses between them, and the thickest of those covers 4 sizes at once. Thickness here is a sheet gauge the sizes were assigned to, not a value scaled from the bolt.

Eight thicknesses, thirteen sizes

Thickness h (mm)Sizes at that thicknessCount
0.5M31
0.8M41
1.0M51
1.6M6 M82
2.0M101
2.5M12 M142
3.0M16 M18 M20 M224
4.0M241

5 of the 13 sizes reuse the thickness of the size below them — M8, M14, M18, M20, M22 — which is how 13 rows produce 8 values. The widest single value is 3.0 mm, covering M16, M18, M20, M22.

The steps in between are not even, and the steepest one is not alone. M3 to M4 (0.5 to 0.8 mm) and M5 to M6 (1.0 to 1.6 mm) are each 1.60 times — 60.0% more metal on bolts that grew 33.3% and 20.0% respectively. 5 of the 12 steps add nothing at all, and every other step lands below 1.60×.

That is what a mill produces. Sheet and strip come in a short list of thicknesses, so a size that does not need a new gauge gets the one below it. The gauge leads and the size follows.

One sheet, two sizes

The pair that makes it visible is M6 and M8. Both take a 1.6 mm washer. The M8 bolt is 33.3% larger in diameter, and the washer is the same piece of metal.

Turn those two rows into a ratio and the table looks inconsistent in the opposite direction. The M6 washer is 26.7% of its own bolt diameter; the M8 washer is 20.0% of its. Nothing changed except which bolt the washer sits under.

Across the whole table that ratio runs from 26.7% at M6 to 13.6% at M22 — a spread of 1.96 between two washers from the same standard, neither of them unusual. The absolute numbers move the other way: 3.0 mm on the M22 is 1.88 times the 1.6 mm on the M6, and it is the *thinner* washer for its bolt.

The bore steps at M12

The bore is not the nominal diameter, and it is not a tolerance either: it is a fixed allowance per size, enough to clear the thread and still centre the washer. In the metric table the allowance starts at 0.2 mm, climbs by tenths, and then doubles.

StandardBore clearance d1 − dSizes
ISO 70890.2 mmM3
ISO 70890.3 mmM4 M5
ISO 70890.4 mmM6 M8
ISO 70890.5 mmM10
ISO 70891.0 mmM12 M14 M16 M18 M20 M22 M24
ASME B18.22.10.031 in1/4 3/8 1/2 5/8
ASME B18.22.10.0315 in5/16
ASME B18.22.10.062 in3/4
DIN 1270.1 mmM3 M4 M5 M6 M8
DIN 1270.2 mmM10 M12 M14 M16 M20
DIN 1270.5 mmM24

The jump is at M12: 0.5 mm on M10, 1.0 mm from M12 up, and 7 of the 13 rows share that one number.

The inch table makes the same move a rung later. 4 of its 6 sizes sit at 0.031 in, the 5/16 row reads 0.0315 in (its bore is 0.344 in against a 0.3125 in nominal), and 3/4 takes 0.062 in — exactly double.

Spring washers run tighter than either, in three steps of their own: 0.1 mm on 5 sizes, 0.2 mm on 5 sizes, 0.5 mm on 1 size. That is a fit, not a clearance — a lock washer is meant to grip the bolt it sits on.

Twice the bolt, only in the middle

"Outside diameter is twice the bolt" is a useful rule of thumb with a narrow home. The metric table holds it exactly — not approximately, exactly — for 6 consecutive sizes, M5 through M14.

Below that run the washer is proportionally wider: 2.33 at M3, 2.25 at M4. Above it the washer falls short: 1.88 at M16, and the lowest in the table at 1.77 on M22. So the rule covers the middle of the range and nowhere else — which is the same shape as the thickness ladder, on a different column.

DIN 125 A is ISO 7089, cell for cell

This database carries both numbers, and they are the same table: 13 rows, identical bore, identical outside diameter, identical thickness, row for row. The DIN 125 A page and the ISO 7089 page print the same grid.

That is worth stating exactly, because "the DIN number was replaced by the ISO number" is usually shorthand for a re-dimensioning, and readers reasonably assume something moved. Here nothing moved. It is also not a general claim about DIN and ISO numbering: it is a measurement of this one pair, and the interchangeability article is where the general question belongs.

A spring washer is not a thin flat washer

SizeSection s (mm)Free height h (mm)h / s
M30.81.62.00
M40.91.82.00
M51.22.42.00
M61.63.22.00
M82.04.02.00
M102.24.42.00
M122.55.02.00
M143.06.02.00
M163.57.02.00
M204.08.02.00
M245.010.02.00

The first thing the table shows is that the two families are not comparable column for column. h on the DIN 127 page is free height, the gap across the split when nothing is clamping it; the material thickness is s. Read h as thickness and the M24 lock washer looks 10.0 mm thick against a 4.0 mm flat washer for the same bolt — a spring's opening compared with a sheet.

Read the right column and a rule appears that the flat table does not have: h is 2.00 times s on every one of the 11 sizes. 11 rows landing on the same ratio is what a geometry looks like, not what 11 independent choices look like. Whether the standard derives h from s or the other way round is not something this database can settle; what it can say is that the two move together exactly, on every size here — while the flat washer's thickness has no such rule, which is why that column has to step.

Spring washers also carry no outside diameter in this database, so nothing here says how wide one is, and no outside-diameter comparison between the two families is possible from these rows.

What this page does not say

  • Tolerances. The table gives nominal thickness, not the permitted range. A supplier's 3.0 mm sheet and the standard's 3.0 mm are not the same statement.
  • Material and hardness. These rows carry dimensions only. Steel grade, coating and hardness are not encoded, so nothing here says whether a washer will deform under the joint.
  • Bearing pressure. Spreading clamp load is the washer's job, and computing that needs the head or nut bearing face — a different table this article does not touch.
  • The rest of either product range. 43 rows is what this database carries: 13 metric flat, 13 of the same grid under the older number, 11 spring and 6 inch. Sizes outside these are not missing data to be guessed at.

How to use this

  1. Do not scale a washer from a bolt. Look the size up, then check the thickness against the joint — 3.0 mm covers M16, M18, M20, M22, so a thicker washer is not bought by moving up one size.
  2. When a drawing gives a thickness and no size, the ladder reads backwards: it names every size that uses that gauge, and the nearest substitute is usually one of them.
  3. Read the bore allowance as part of the table, not as a defect. 1.0 mm of clearance on an M12 bolt is the standard's own number; a washer measuring 13.0 mm across the bore is correct.
  4. On a lock washer, quote s when you mean thickness. The free height is a different dimension, and it is 2.00 times larger on every size here.
  5. For a metric flat washer either number will do, because the two are identical. Use the washers hub when the question is which family rather than which size.

The same shape of question — a number that looks like it belongs to the part but belongs to the table — is what the outside diameter of a bearing turns on.