DIN 529 F Anchor Bolt, Form F
Form F is the only one of the five with an s column, and in its row of the 2010 table g and s carry the same value at every diameter from M8 to M48 — 6, 8, 10, 14, 18, 22, 26, 30, 36, 42. Two identical columns are printed here as two columns because the standard prints two; whether that is a coincidence of the form or a duplicate in the printing is not something this page can settle. Its head width is the smallest of the five forms and its sizes stop at M48.
Where it is used
Form F is the only form of DIN 529 with an s column, and in the 2010 edition its g and s carry the same value at every diameter printed, M8 to M48. Its head is the smallest of the five forms at every diameter, which makes it the form to reach for when the pocket is tight; its a, c, g and s columns all stop at M48. The fixing works the same way as the rest of the family — head embedded, nut on the free thread — and the standard states no pull-out resistance for any of the five forms.
How to choose it
Read a and c against the pocket, exactly as for forms C and E, whose head width row form F shares with neither: F's a values are smaller again. The two columns g and s being equal at every size is worth knowing before ordering, because a drawing that dims one of them and not the other is not thereby under-specified — but which of the two the drawing means is not something this table can settle, and that is a question for whoever wrote the drawing. Thread and length follow the family: nut and washer on the free end, length from plate thickness plus embedment.
Dimensions10 sizes · millimetres
| Thread d | Pitch P (mm) | Thread length b (mm) | a (mm) | c (mm) | g (mm) | s (mm) |
|---|---|---|---|---|---|---|
| M8 | 1.25 | 20 | 14 | 50 | 6 | 6 |
| M10 | 1.5 | 25 | 16 | 50 | 8 | 8 |
| M12 | 1.75 | 30 | 20 | 55 | 10 | 10 |
| M16 | 2 | 40 | 25 | 85 | 14 | 14 |
| M20 | 2.5 | 50 | 30 | 95 | 18 | 18 |
| M24 | 3 | 60 | 35 | 120 | 22 | 22 |
| M30 | 3.5 | 75 | 45 | 130 | 26 | 26 |
| M36 | 4 | 90 | 55 | 190 | 30 | 30 |
| M42 | 4.5 | 105 | 65 | 200 | 36 | 36 |
| M48 | 5 | 120 | 75 | 220 | 42 | 42 |
Nominal dimensions in millimetres as published in DIN 529 F. Tolerances, material requirements and marking are defined separately by the issuing body.
Available sizeslinked to individual specification pages
Thread referencesused by the sizes above
Fitting and interchange notes
The g and s columns of form F are identical cell for cell, 6, 8, 10, 14, 18, 22, 26, 30, 36 and 42 mm. Two identical columns are reproduced as two columns because the standard prints two; collapsing them here would hide the fact that the standard distinguishes them, and inventing a difference between them would be worse. Form F's table stops at M48, so this page does too. The family-wide caveats are unchanged: the letters carry no written definition in any reproduction this site can check, the head is therefore not drawn, the shank shape is left to the manufacturer, and there is no mass table — with no mass calculated in its place, because the volume would depend on the one feature the standard leaves open. Commercial lengths run 80 to 3200 mm.